v1.0 (EN)
Microphone
Important battery information
Play
Video quality selector
HQ: High Quality mode
webQ: Web quality mode
Using your camcorder
Carrying handle
Refer to “USB Connector ARM”for
more information.
•
•
•
Any battery may leak electrolyte if mixed with a different battery type, if inserted
incorrectly, or if all batteries are not replaced at the same time.
Any battery may leak electrolyte or explode if disposed of in fire or an attempt is made to
charge a battery not intended to be recharged.
Discard leaky batteries immediately. Leaking batteries can cause skin burns or other
personal injury. When discarding batteries, be sure to dispose of them in the proper
manner, according to your state/provincial and local regulations.
1. Press PLAY/PAUSE to start playback of the most recent recording or the selected video.
To select another video, refer to Selecting videos.
2. Press and hold PLAY/PAUSE for three seconds to play all videos.
LCD screen
QuickStartGuide
EZ210 RCA Small Wonder Camcorder
Turn on/off
•
•
The selected setting (HQ or webQ) appears on the display screen during recording.
The HQ setting is recommended when planning to view video on a TV directly from the
camcorder.
1. Press ON/OFF to turn on.
2. Press and hold ON/OFF to turn off.
•
If no video is selected after playback has finished, recording mode will resume after 5 seconds.
Mirror for self recording
Lens
•
Camcorder will automatically turn off after 2 minutes if not in use.
Search forward/backward:
Right view
Congratulations on purchasing your new RCA Small Wonder Camcorder.
Please read these instructions for quick tips on using the product.
Settings
HQ
webQ
Quality
Near DVD 60 minutes
GOOD 240 minutes
Approximate recording duration*
•
•
Hold down to fast forward the selected video during playback.
Hold down to fast rewind the selected video during playback.
Record
Press and release the red RECORD button (after
“READY”appears on the screen) to begin recording.
Setting date and time
1. Press or to shift among month, date, hour and minute and press + or – to set the
date/time values.
2. Press or to select DONE and then press the red RECORD button to save settings. Or
press DELETE to exit without saving.
* Recording duration is based on 2 GB SD card. Actual recording capacity
depends on type of video content being recorded.
Pausing video playback:
Getting started
•
Press PLAY/PAUSE to pause playback (a pause indicator II and the remaining playback
time flash at the top left corner of the screen).
Recording indicator
While recording:
Battery installation
Left view
•
A red and the elapsed time appears at the top
left corner of the screen.
1. Push (to the right) and hold the front cover lock at the bottom of the camcorder.
2. Slide the front cover down and then lift up to open.
3. Replace or install 2 AA batteries.
•
Press PLAY/PAUSE again to resume playback.
USB Connector ARM
Extending the USB Connector ARM:
1. Press down on the release button of the detachable carrying
handle (refer to illustration below).
•
Date and time setting can be accessed by pressing and holding PLAY/PAUSE and ON/OFF
together while the camcorder is turned off.
•
The red recording light on the camcorder front
turns on.
AV output
Selecting videos:
Audio/Video output for connecting to TV or other
AV equipment with the included AV cable.
•
•
Make sure you align the battery polarities as indicated.
•
•
Press and release to cue the next video.
Press and release to cue the previous video.
In the case of low battery, a low battery icon (
) will flash on the screen. Please change
2. Pull and remove the carrying handle.
3. Press down on the USB Connector ARM button.
4. Slide out to extend the Connector ARM.
•
Refer to “Viewing videos on TV” and “Recording videos to VHS
tape or DVD” overleaf for more information.
Pausing a recording:
batteries when battery icon is flashing.
SD memory card
•
•
Press PLAY/PAUSE.
•
Alkaline batteries are recommended for best results under normal use. For extended video
shooting, Energizer e2 Lithium AA batteries are recommended.
Front view
•
An SD memory card is included and already inserted in the camcorder. It is installed
between the batteries in the front compartment.
Delete
A pause indicator II replaces the red at the top
left corner and “Recording Paused” flashes in the
middle of the screen.
•
•
Refer to “Connecting to a PC” overleaf for more information.
Use USB Extension Cable (provided) if USB Connector ARM is obstructed or space does not
permit connection to PC.
1. Press DELETE and the last recording and “DELETE VIDEO ?” appear on the screen.
4. Replace the front cover and slide up to lock.
Bottom view
•
•
To remove card, simply pull the card out from the card slot.
To insert card, align card with Card Symbol on camcorder and slide in until a click is heard.
The card icon ( ) appears on the screen with memory card inserted.
•
To select another video, refer to Selecting videos.
Front cover
Refer to Battery installation for more
information.
3
2. Press and hold DELETE until the selected video is deleted.
•
To resume recording, press and release PLAY/
PAUSE again.
•
To retreat the ARM, press down on the USB Connector ARM button and slide in.
3. To delete all videos, press & hold DELETE for 3 seconds and then repeat step 2.
SD card
2
1
2
To protect the lens, use
the lens cover (supplied)
when not in use.
Take photo
4
Stop
Camcorder strap hole
•
Press and release WEB PHOTO to take photo.
1
4
While playing or recording, press and release the red
RECORD button to stop the playing or recording.
Back view
Tripod screw mount
Front cover lock
3
1
2
Zoom
Volume
During playback:
Replacing the carrying handle
Audio speaker
Before or during recording:
•
•
Press + to zoom in.
Press – to zoom out.
•
•
Press + to increase volume.
Press – to decrease volume.
Front compartment
|