M52757FP
Wide Band Analog Switch
REJ03F0195-0201
Rev.2.01
Mar 31, 2008
Description
The M52757FP is a semiconductor integrated circuit for the RGB interface. The device features switching signals input
from two types of image sources and outputting the signals to the CRT display, etc. The frequency band of video
signals is 250 MHz, acquiring high-resolution images, and are optimum as an interface IC with high-resolution CRT
display and various new media.
It includes Sync-separator, Video-signal-detector, and Sync-on G detector (SOG-DET.).
Features
•
•
•
Frequency band width: R.G.B
Input level: R.G.B
Video signal-detector
Responsive frequency:
Input level:
250 MHz
0.7 VP-P (Typ.)
to 50 MHz
0.7 VP-P (Typ.)
Detected level:
150 mV (Typ.)
(Measure botto
•
•
Only the G channel is proved with buffer video outpu
It is possible to save the consumption current by st2, 4, 6, 20, 24, 30, 33, 35 because
SOG-DET can be operated with only VCC5 (Pin
Include Sync Separation, Video signal detec.
•
Application
Display monitor
Recommended Opera
Supply voltage range:
Rated voltage:
5 V
REJ03F0195-0201 Rev.2.01 Mar 31, 2008
Page 1 of 6
M52757FP
Absolute Maximum Ratings
(Ta = 25°C)
Item
Supply voltage
Symbol
Ratings
7.0
Unit
V
VCC
Power dissipation
Pd
1068
mW
°C
°C
V
Operating temperature
Topr
Tstg
Vopr
Vopr'
−20 to +85
−40 to +150
5.0
Storage temperature
Recommended operating supply voltage
Recommended operating supply voltage range
Electrostatic discharge
4.75 to 5.5
±200
V
Sarge
V
Thermal Derating (Maximum Rating)
1250
1068
1000
750
500
250
0
−25
0
125
150
a (°C)
REJ03F0195-0201 Rev.2.01 Mar 31, 2008
Page 3 of 6
M52757FP
Electrical Characteristics
(VCC = 5 V, Ta = 25°C)
Limits
Test
Item
Symbol
Unit
mA
Point (s)
Input
SW18
OPN
OPN
Min
45
3
Typ Max
Circuit current 1
ICC1
5
65
5
85
7
A
Circuit current 2
ICC
mA
15
<RGB SW>
Output DC voltage 1
Output DC voltage 2
Output DC voltage 3
Output DC voltage 4
Maximum allowable input 1
Maximum allowable input 2
Voltage gain 1
Vdc1
Vdc2
Vdc3
Vdc4
VImax1
VImax2
Gv1
1.1
1.1
1.5
1.5
0.9
0.9
1.6
1.6
0.5
0
1.9
1.9
1.3
1.3
V
V
29, 32, 35
29, 32, 35
27
OPN
GND
OPN
GND
GND
GND
GND
0.5
V
0.5
V
27
1.4
VP-P
VP-P
dB
dB
dB
dB
dB
dB
1, 3, 5
1, 3, 5
7, 9, 11
1, 3, 5
1.4
7, 9, 11
29, 32, 35
−0.1
−0.6
−0.1
−0.6
−0.6
−0.6
−1.0
−1.0
−1.0
−1.0
1.1
0.6
1.1
0.6
0.6
0.6
1.0
1.0
Relative voltage gain 1
Voltage gain 2
∆Gv1
Gv2
Relative to measured values above
29, 32, 35 7, 9, 11 OPN
Reto measured values above
0.5
0
Relative voltage gain 2
Voltage gain 3
∆Gv2
Gv3
0
3
9
GND
OPN
GND
Voltage gain 4
Gv4
0
Freq. characteristic 1 (100 MHz) Fc1
0
5
Relative Freq. characteristic 1
∆Fc1
0
red values above
, 9, 11 OPN
measured values above
Freq. characteristic 2 (100 MHz) Fc2
0
Relative Freq. characteristic 2
∆Fc2
0
Freq. characteristic 1 (250 MHz) Fc3
Freq. characteristic 2 (250 MHz) Fc4
−3.0 −
35
32, 35
9, 32, 35
1, 3, 5
7, 9, 11
1, 3, 5
GND
OPN
−3.0
Crosstalk between 2 inputs 1
(10 MHz)
CTI1
−50
−50
−30
−30
GD to OP
Crosstalk between 2 inputs 2
(10 MHz)
CTI2
5
−35
−40
−40
−25
−25
B
dB
dB
dB
dB
dB
dB
29, 32, 35
29, 32, 35
29, 32, 35
29, 32, 35
29, 32, 35
29, 32, 35
29, 32, 35
7, 9, 11
1, 3, 5
OP to GD
GD to OP
OP to GD
GND
Crosstalk between 2 inputs 3
(100 MHz)
C
Crosstalk between 2 inputs 4
(100 MHz)
7, 9, 11
1, 3, 5
Crosstalk between chan
(10 MHz)
C3
CTC4
Crosstalk between channel 2
(10 MHz)
7, 9, 11
1, 3, 5
OPN
Crosstalk between channel 3
(100 MHz)
GND
Crosstalk between channel 4
(100 MHz)
7, 9, 11
OPN
Pulse characteristic 1
Tr1
Tf1
Tr2
Tf2
1.6
1.6
1.6
1.6
2.5
2.5
2.5
2.5
ns
ns
ns
ns
29, 32, 35
29, 32, 35
29, 32, 35
29, 32, 35
1, 3, 5
1, 3, 5
GND
GND
OPN
OPN
Pulse characteristic 2
7, 9, 11
7, 9, 11
<SYNC SEP>
Sync input min. level
SYrv
0.2
4.5
4.9
0.2
60
VP-P
V
25
25
25
25
25
26
26
26
26
26
Sync-sep output Hi level
Sync-sep output Low level
Sync-sep output delay time 1
Sync-sep output delay time 2
SYVH
SYVL
TdSf
0.4
V
ns
ns
TdSb
60
REJ03F0195-0201 Rev.2.01 Mar 31, 2008
Page 4 of 6
M52757FP
Electrical Characteristics (cont.)
Limits
Typ
Test
Point (s)
Item
<SYNC DET>
Symbol
Unit
Input
SW18
Min
Max
Min. detectable Sync amplitude
Max. detectable Sync width
Sync-DET output high level
Sync-DET output low level
Max. allowable input noise level
<VIDEO DET>
SDETrv
SDETrt
SDVH
0.2
4.0
4.9
0.2
VP-P
µs
V
14
14
14
14
14
3, 9
3, 9
3, 9
3, 9
3, 9
4.5
SDVL
0.4
V
SDETnv
0.05 VP-P
Allowable input DC range
VDinV
2.0
2.4
0.7
2.8
1.0
V
19, 21, 23 19, 21, 23
Allowable input amplitude range VDin
VP-P 19, 21, 23 19, 21, 23
Min. detectable input level
Max. allowable input noise level
Max. input pulse width
VDETrv
0.15
VP-P
VP-P
ns
17
17
17
17
19, 21, 23
19, 21, 23
19, 21, 23
19, 21, 23
19, 21, 23
VDETnv
VDETrt
SDVH
0.1
10.0
4.8
0.7
Video-DET output Hi level
Video-DET output Low level
4.2
V
SDVL
1.0
V
REJ03F0195-0201 Rev.2.01 Mar 31, 2008
Page 5 of 6
M52757FP
Package Dimensions
JEITA Package Code
P-SSOP36-8.4x15-0.80
RENESAS Code
Previous Code
36P2R-D
MASS[Typ.]
0.5g
PRSP0036GA-B
36
19
F
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
18
1
Index mark
*2
D
Dimension in Millimeters
Reference
Symbol
A1
Min Nom Max
D
E
14.8 15.0 15.2
8.2 8.4 8.6
2.05
*3
bp
y
e
A2
A
2.35
0.1 0.2
A1
bp
c
0
0.3 0.35 0.45
0.18 0.2 0.25
0°
8°
HE
e
11.63 11.93 12.23
0.65 0.8 0.95
0.10
F
y
L
0.3 0.5 0.7
REJ03F0195-0201 Rev.2.01 Mar 31, 2008
Page 6 of 6
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Notes:
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes
warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property
rights or any other rights of Renesas or any third party with respect to the information in this document.
2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including,
but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples.
3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass
destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws
and regulations, and procedures required by such laws and regulations.
4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this
document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document,
please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be
5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a
result of errors or omissions in the information included in this document.
6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability
of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular
application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products.
7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications
or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk uman injury or which require especially high quality
and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combntrol, aerospace and aeronautics, nuclear power, or
undersea communication transmission. If you are considering the use of our products for such purposes, pleRenesas sales office beforehand. Renesas shall
have no liability for damages arising out of the uses set forth above.
8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed
(1) artificial life support devices or systems
(2) surgical implantations
(3) healthcare intervention (e.g., excision, administration of medication, etc.)
(4) any other purposes that pose a direct threat to human life
Renesas shall have no liability for damages arising out of the uses set forth in the above and cts in any of the foregoing
applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated coployees against any and all
damages arising out of such applications.
9. You should use the products described herein within the range specified by Renesas, g, operating supply voltage range,
movement power voltage range, heat radiation characteristics, installation and other no liability for malfunctions or damages
arising out of the use of Renesas products beyond such specified ranges.
10. Although Renesas endeavors to improve the quality and reliability of its productuch as the occurrence of failure at a certain
rate and malfunctions under certain use conditions. Please be sure to implemssibility of physical injury, and injury or damage
caused by fire in the event of the failure of a Renesas product, such as safeg but not limited to redundancy, fire control and
malfunction prevention, appropriate treatment for aging degradation or an, since the evaluation of microcomputer software
alone is very difficult, please evaluate the safety of the final products or
11. In case Renesas products listed in this document are detached from are attached or affixed, the risk of accident such as
swallowing by infants and small children is very high. You should iproducts may not be easily detached from your products.
Renesas shall have no liability for damages arising out of such d
12. This document may not be reproduced or duplicated, in any foapproval from Renesas.
13. Please contact a Renesas sales office if you have any queshis document, Renesas semiconductor products, or if you have
any other inquiries.
RENESAS SALES OFFICE
Renesas Technology Amer
450 Holger Way, San Jos
Tel: <1> (408) 382-7500,
Renesas Technology Europ
Dukes Meadow, Millboard Roadamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <40
Renesas Technology (Shanghai) Co.
Unit 204, 205, AZIACenter, No.1233 Lujiaing Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2377-3473
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .7.2
|